800+ IT
News
als RSS Feed abonnieren📚 Need help to set up a raid controller (LSI 9341-8i, Ubuntu 20.04)
💡 Newskategorie: Linux Tipps
🔗 Quelle: reddit.com
I'm trying to install an LSI 9341-8i raid card in a workstation (MSI TRX40 pro 10G, linux kernel 5.8.0-63-generic) and am running into trouble possibly at getting the linux driver operational. I am able to get into the card Bios and set the drives as JBOD (for use with ZFS). I've downloaded and installed the latest linux driver from Broadcom. The module shows up in lsmod:
megaraid_sas 163840 0
In lshw, the card appears as "unclaimed":
*-raid UNCLAIMED description: RAID bus controller product: MegaRAID SAS-3 3008 [Fury] vendor: Broadcom / LSI physical id: 0 bus info: pci@0000:03:00.0 version: 02 width: 64 bits clock: 33MHz capabilities: raid pm pciexpress vpd msi msix cap_list configuration: latency=0 resources: ioport:3000(size=256) memory:e8200000-e820ffff memory:e8100000-e81fffff memory:e8000000-e80fffff
And during boot, dmesg shows:
[ 0.953207] megaraid_sas: loading out-of-tree module taints kernel. [ 0.962379] megaraid_sas: module verification failed: signature and/or required key missing - tainting kernel [ 0.965748] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0 [ 0.965750] piix4_smbus 0000:00:14.0: Using register 0x02 for SMBus port selection [ 0.965813] megasas: 07.717.02.00 [ 0.966649] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20 [ 0.967046] megaraid_sas 0000:03:00.0: BAR:0x1 BAR's base_addr(phys):0x0x00000000e8200000 mapped virt_addr:0x00000000b2dc5478 [ 0.967048] megaraid_sas 0000:03:00.0: FW now in Ready state [ 0.967050] megaraid_sas 0000:03:00.0: 63 bit DMA mask and 32 bit consistent mask [ 0.967247] megaraid_sas 0000:03:00.0: firmware supports msix : (96) [ 0.967289] dca service started, version 1.12.1 [ 0.967957] ahci 0000:47:00.0: version 3.0 [ 0.968302] ahci 0000:47:00.0: AHCI 0001.0301 32 slots 8 ports 6 Gbps 0xff impl SATA mode [ 0.968304] ahci 0000:47:00.0: flags: 64bit ncq sntf ilck pm led clo only pmp fbs pio slum part sxs [ 0.969646] megaraid_sas 0000:03:00.0: requested/available msix 49/49 [ 0.969647] megaraid_sas 0000:03:00.0: current msix/online cpus : (49/48) [ 0.969648] megaraid_sas 0000:03:00.0: RDPQ mode : (disabled) [ 0.969651] megaraid_sas 0000:03:00.0: Current firmware supports maximum commands: 272 LDIO threshold: 237 [ 0.969723] megaraid_sas 0000:03:00.0: Configured max firmware commands: 271 [ 0.969754] scsi host1: ahci [ 0.969906] scsi host2: ahci [ 0.969922] megaraid_sas 0000:03:00.0: Performance mode :Latency [ 0.969923] megaraid_sas 0000:03:00.0: FW supports sync cache : Yes [ 0.969925] megaraid_sas 0000:03:00.0: megasas_disable_intr_fusion is called outbound_intr_mask:0x40000009 ... [ 0.994381] megaraid_sas 0000:03:00.0: Init cmd return status FAILED for SCSI host 0 [ 0.995154] megaraid_sas 0000:03:00.0: Failed from megasas_init_fw 6752
When trying to access the card with the StorCLI utility from Broadcom, I get:
$ /opt/MegaRAID/storcli/storcli64 /c0 show CLI Version = 007.1705.0000.0000 Mar 31, 2021 Operating system = Linux 5.8.0-63-generic Controller = 0 Status = Failure Description = Controller 0 not found
Any help, suggestions or hints on how to investigate this would be really appreciated. It is my first time setting up a raid card, so I might very well missing an evident step...
Suggestion of more targeted forums / subreddit welcome too!
[link] [comments] ...